+607 557 6078       +607 557 6079
Select Page
Australia reinforcing wire mesh for reinforcement of concrete

REINFORCING WELDED WIRE MESH (CUT AND BEND SOLUTION MESH)

CUT AND BEND REINFORCING MESH – RM SPECIAL CUSTOMIZED RUN MESH AND CUT & BEND SOLUTION MESH

RM reinforcing wire mesh also come with design drawing and customized special run mesh. 

Advantages of RM customized special run mesh and cut & bend solution mesh:

REINFORCING WELDED WIRE MESHMinimized the percentage of wastage

REINFORCING WELDED WIRE MESHBoost the speed of construction

REINFORCING WELDED WIRE MESHReducing on site labor

REINFORCING WELDED WIRE MESHBetter Utilization of on-site space and logistics.

REINFORCING WELDED WIRE MESHAble to cut & Bend to suit specific prefabricator’s concrete. 

The large warehouse factory or large compound areas in industrial floors made it possible for substantial benefits to be obtained by utilizing our RM customized special run mesh.  For example, we can produce up to 9m in length compared to the standard mesh of 6m.

 

REINFORCING WELDED WIRE MESH SPECIFICATIONTension Laps

Tension laps length should be at least equal to the design tension anchorage length necessary to develop the required stress in the reinforcement.

 

Compression Laps

The length should be at least 25% more than the compression anchorage length.  In the detailing of steel fabric, two cross welds are provided to transfer the stresses.  In sidelaps of one-way slabs, half yield strength laps with overlap of only one cross weld are acceptable.  This is commonly used in top (negative) reinforcement.

Full yield strength lap should always be provided when lap length is not specific.

 

MESH ORIENTATION

Standards Fabric Main Cross
Australia reinforcing mesh orientation Square Fabric  200mm Main Wire Spacing 200mm Cross Wire Spacing
 Australia reinforcing mesh orientation Rectangular Fabric 100mm Main Wire Spacing 200mm Cross Wire Spacing
 Australia reinforcing mesh orientation Rectangular Fabric 100mm Main Wire Spacing 400mm Cross Wire Spacing
 Australia reinforcing mesh orientation Small Square Fabric  100mm Main Wire Spacing 100mm Cross Wire Spacing

 

REINFORCING WELDED WIRE MESH (CUT AND BEND SOLUTION MESH)BEND

End anchorage in the form of hooks and bends should only be used to meet specific design requirements.

  • Commercial Construction
  • Housing Construction
  • Civil Construction

MESH APPLICATION:

  Precast Concrete

Accuracy is the key manufacturing mesh for precast concrete applications such as walls, culverts, drainage pipe.  All CUT & BEND precast mesh is manufactured to ensure that if fits perfectly within precast moulds, steelfixing.

   Pipe Encasement

We supply pairs of CUT & BEND mesh sections that can greatly simplify steelfixing for roadways with high trafffic loads which require Pipe Encasement.

   Mining Applications

Sheets of mesh can be cut to specific dimensions in order to suit a variety of mining applications and improving the handling of mesh in difficult underground conditions.  All mesh for mining applications is taylor-made for safety improvement and galvanized for corrosive environments.

   Various Types of Footings

We are able to CUT & BEND mesh to suit a wide range of footing requirements.

RM Reinforcing Wire Mesh is certified by the standard & Industrial research of Malaysia (SIRIM), MS145 and is able to comply to the following standards from various international standards.

Country Standards Title Yeild Strenght (N/mm2)(MPa)

MALAYSIA

MS 144:2006

MS 144:2014

Cold-reduced steel wire for the reinforcement of Concrete products 500
MALAYSIA

MS 145:2006

MS 145:2014

Steel fabric for reinforcement of concrete 500
MALAYSIA

MS 146:2014

Steel for the reinforcement of concrete – Weldable reinforcing steel – Bar, coil and decoiled products 500

BRITISH

BS: 4483:2005

Steel fabric for reinforcement of concrete 500

SINGAPORE

SS 561:2010

Steel fabric for reinforcement of concrete 500

AUSTRALIA

AS/ANZS 4671:2001

Steel fabric for reinforcement of concrete 500
  • Manufactured in Malaysia
  • Third party accredited by CIDB, SIRIM, STANDARDS MALAYSIA

RM Wire Industries provide delivery services for this product.

Please contact us for more information.

The following downloads are available:

Please contact us for more information.


Need to get in touch with one of our team? Simply fill out the form below. We’d love to hear from you!



MILD STEEL ROUND BAR, ROUND STEEL BAR

MILD STEEL ROUND BAR, ROUND STEEL BAR RM mild steel round bar (round steel bar) can come with various diameters and finished with smooth and plain surface.  Adhering to international standards, RM plain smooth sound bar is produced by the steel wire rids.  RM mild...

Summary
product image
Author Rating
1star1star1star1star1star
Aggregate Rating
5 based on 17 votes
Brand Name
RM REINFORCING WELDED WIRE MESH (CUT AND BEND SOLUTION MESH)
Product Name
RM REINFORCING WELDED WIRE MESH (CUT AND BEND SOLUTION MESH)
Price
USD 600/ton - 700/ton
Product Availability
Available in Stock